Dontronics Home Page  DT006 Prices.
 


Order This Item Now
Dontronics Catalog
View Shopping Cart Contents
 
 
 
 
 
 
 
 
 
 

 

Home Products Site Map Order Contact What's New Books Free Files Links FAQ
Order This Item Now Dontronics Catalog View Shopping Cart Contents

You will need a suitable power supply (plug pack/wall wart) that will supply 9 to 12 Volts AC or DC @300ma or more, to power this unit up. As the input has a diode bridge, it isn't polarity conscious, so an AC or DC supply can be used.  There is no power supply included in the kit or assembled and tested unit, as these can be usually purchased locally for less than the cost of postage, and will be designed to match local input voltages and power outlets available. EG: 120/240 AC.

DT006-K
Note *** This kit doesn't include power supplies, cables, or boxes.

Items Supplied in Kit.
DT006 PCB
Crystal/Resonator 3 pin socket
16 pin machine pin socket
20 pin machine pin socket
Resistor Network (10P9R-1K)
C1-1000uf Electrolytic @25 Volts
VR1-7805 +5 Voltage regulator in TO-220 case
Suitable heat sink for the Regulator.
D1-Diode Bridge D1 WO2 (or WO4 type)
J4-2.5mm (or 2.1mm) DC Input plug. PCB mount.
J6-DB-9 right angle PCB mount connector.
J7-DB-25 Male right angle PCB mount connector.
3 x 4 leg push-button Switches.
J9-Set of male header pins at .1" centers. (8 x 2 format)
U3-AT90S2313-10-PC 10Mhz 20 pin DIP
X1-3 leg resonator to suit Micro speed..
U1-MAX-232 E2 (or equivalent)
TL8- 8 x .1" test links.

"rAVeR!"
DT006-K Total 
Postage: Australia  , International 
If you purchase the DT006-K, we will throw in the Simm Socket, and a set of male/female 30 pin headers at no extra charge.

I'll repeat that, as many users stlll order a set of  connectors:
If you purchase the DT006-K, we will throw in the Simm Socket, and a set of male/female 30 pin headers at no extra charge.

You can power this unit with a Plug Pack or Wall Wart with 9V to 12V AC or DC at 300ma or more.



"rAVeR!" SimmBus Connectors:
A Dual 30 pin Simm Socket and a set of 30 pin Female and Male headers. See simcon.html
DT006-EXP Total

"rAVeR!" Fully Assembled and tested Kit.

As shown in the picture above, however as an introductory bonus, the Simm Socket and 30 pin Female header are fitted. A male header is also included for the expansion of the Simm Bus. Simply power it up and watch the LEDs run, as they are programmed with the rAVeR.bas demo program.
DT006-A&T Total 
Postage: Australia  , International 


Please Note ****
All of the hardware items listed on this page require postage costs to be added. Only bare printed circuit boards have free postage.


"rAVeR!" DB-25 male to DB-25 female cable.
RAVER Cable: 
The cable supplied is now a standard 25 wire straight through cable.

Hardware for Individual Units:
You can purchase as little or as much as you like, as long as the total is more that $20AUD.
"rAVeR!"

RAVER Kit A:
AT90S2313-10-PC 10Mhz 20 pin DIP, 2K Flash. $15AUD
10Mhz Resonator $2AUD
DT104 $ 8AUD

RAVER Kit A is a short kit of the above parts. Three items only. A bare board, a Micro, and a resonator.


"rAVeR!"
RAVER Kit B: 
AT90S2313-10-PC 10Mhz 20 pin DIP, 2K Flash. $15AUD
10Mhz Resonator $2AUD
DT006 $ 20AUD

RAVER Kit B is a short kit of the above parts. Three items only. A bare board, a Micro, and a resonator.


And also available is the assembled and tested SIMM101 module. This is a DT104 work-alike, but uses surface mount devices. Plenty of proto area on a 1" SimmStick.
Or just buy the bare boards. All of the below boards are post free.

DT104 x 1 PCB: 
DT104 x 5 PCB:  15% Off
DT104 x 10 PCB: 20% Off

DT006 x 1 PCB: 
DT006 x 5 PCB:  15% Off
DT006 x 10 PCB: 20% Off

Dontronics Home Page


Copyright © 1996-2005 Dontronics
Order This Item Now Dontronics Catalog View Shopping Cart Contents